LOCKPICKING,VARIOUS METHODS

LOCKPICKING BY LOCKSMITH TRAINING MERSEYSIDE.

Definition of "Lockpicking" - The means of opening a lock mechanism by the intrusion of a tool or mechanical device, other than the normal operating key. This tool can be as simple as a bent paper clip or an expensive pick set or pick gun.

Why Locks Can Be Picked - A lock mechanism becomes vulnerable to picking for two basic reasons: design shortcomings and manufacturing shortcomings. Both of these flaws are directly related to the selling price of the locking device. The design flaw allows a pick, wire, pick key, paper clip, hair pin, knife blade, etc. to be inserted into the keyway in such a manner as to reach and operate the mechanism. Manufacturingshortcomings are found in loose tolerances in the manufacturing process. A tolerance is a necessary sloppiness that is found even in the most expensive of machine products. For example: an .250 in. diameter hole will seldom if ever be exactly .250. The closer to perfection the higher the cost. Therefore,whether in a lock or an automobile, a compromise must be arrived at the engineering level. Basically, anengineer will strive to make the part as cheap as possible and as precise as possible. In lock design a third requirement becomes more important than in some other products and that is strength and durability. The vulnerability of tolerance is usually found in areas such as pin diameters versus pin hole diameters and a row of pin holes deviating from a straight line. Tolerances allow shims to be inserted in the small space necessary between moving parts. Tolerances allow a combination lock to reveal its inner secrets to a skilled manipulator. Tolerances, like the air around us are ever present in any machined product. They cannot be eliminated, only minimized which directly affects the cost of the part. By this time, if you are still reading this book, you may have come to the conclusion that lockpicking is a highly skilled technical complicated operation requiring mechanical savoy and dexterity beyond the majority of Joe Blows. If you have, then you are on the purpose of this book which is to show how difficult picking really is and why the average four thumbed, knuckle dragging, larcenous klutz does well to open a lock with the proper key let alone pick it. A good pick man is about as rare as a good counterfeit plate engraver.

METHODS OF PICKING

Simple Warded Locks - These are typically found in cheaper padlocks, file boxes, luggage, etc. The keys are usually stamped from flat steel and nickel plated. Higher quality warded locks sometimes use corrugated keys in an effort to provide better security and also make the key stronger. A closer look will reveal that each key has the ward cuts in a slightly different position. Internally, the mechanism is basically as shown in Figure 2. In this illustration we see a flat, hairpin type spring that latches into notches in the shackle. Only a portion, usually the tip of the key actuates the spring latch. Turning the key spreads the spring latch apart, releasing the shackle. It is easy to see that a pick for this simple design would only have to be a paper clip or wire with a small "L" bent on one end. A pick key shaped  would also operate any such lock whose keyway would accept it. This is simply a key with all the ward cuts opened up, leaving only the portion on the tip that is necessary to operate the latch spring.

Manufacturers, in an effort to improve the security of this basic locking mechanism, have now added another spring latch with a ward between them. This design complicates efforts to pick it with a bent wire Pin Tumbler Locks - This is by far the most common type lock mechanism found today and is the type which applies to the picking most commonly referred to in articles on security, and distorted on TV. To understand picking this lock we must be familiar, to a limited degree, with its mechanism. Manufacturers have dozens of versions of this mechanism yet they are all basically the same mechanically. have more or less, the average pin tumbler lock has five sets of tumbler pins consisting of a spring, top pin, and bottom pin. The springs and top pins are usually the same length. The bottom pins vary in length to match the depth of the cuts in the key. When a key is inserted into the lock plug this set of pins is raised, compressing the spring. If the proper key has been inserted the bottom pins are all raised until they are flush with the diameter of the plug. This is also known as the shear line. At this point the plug is free to turn and release or activate whatever mechanism it is attached to. To pick this mechanism we must somehow raise these pins or manipulate them so as to allow the plug toturn. Most methods of picking this lock rely on the presence of tolerances as we discussed earlier. In observing the picture and drawings previously mentioned, the tumbler pin holes seem to be the same diameter and also, in a straight line. They are supposed to be and the manufacturer has made a noble effort to do this within the limitations of the selling price of the lock. However, if we were to measure eachpart of the lock  with a precision measuring device, we would find that the diameters of both the pins and holes may vary slightly from pin to pin and from hole to hole. Also, the holes, instead of being in a perfectly straight line will vary slightly from side to side. This variation may be only a fraction of a thousandth of an inch but is enough to aid picking. Picking, in the purest sense, involves applying a very small turning force or torque to the plug and with a feeler pick, carefully probe each bottom pin to find the one or more that seem to be binding more than the rest. With the feeler pick, slowly lift one of these until the top pin clears the shear line. At this time the plug may give slightly in the direction that torque is being applied. This operation is repeated on the remaining pins, at which time the plug will be free to turn. Raking is another method of picking, perhaps the most often used because less skill is required as the lock opens more by chance than by skill. A rake tool has two or three up and down areas and is used in an in and out and up and down motion. The shape together with the random motion may at some unknown moment raise the bottom pins to the right level. If a small torque is being applied at this instant the plug will turn. Another form of raking involves using a diamond shaped tool. This tool is inserted all the way into the keyway and jerked out very very fast. This motion tends to throw the pins apart because of inertia. This opens the area at the shear line permitting the plug to turn.  Yet another form of opening a pin tumbler lock, while not picking in the purest sense, is with a tool known as a snap pick. The mechanical principle behind this method is the same as used with more expensive pick guns. A snap pick  It is kind of an overgrown safety pin looking device made from spring steel. The "pick" portion of this tool is inserted into the keyway and held so that it just touches the bottom pins (all of them at the same time). The thumb presses the bail down then releases it. The bail snaps back hitting the pick. This imparts a sharp rap to the bottom pins. The bottom pins, remaining relatively stationary, transfer this force to the top pins which move upward, compressing the spring. This results in the top and bottom pins being apart at the shear line for ever so small a period of time. If at this time a slight turning force is being applied, the plug will turn. Any who has played pool can appreciate this method. For example: the number one and nine ball are just touching. You strike the nine ball with the cue ball. The nine ball remains stationary while the number one ball moves. This very same principle applies when using a pick gun which we will now discuss. Pick Guns - Perhaps the most misunderstood tool to the uninitiated is the lock pick gun as we choose to call it. Over the years there have existed several versions of this basic tool.

On the outside of the American made version of this tool is stamped the Patent Number1997362. We are amused at the thought of the Chinese ordering a copy of this patent from the U. S. Patent Office as we did. It just so happens that Patent Number 1997362 was assigned on April 9, 1935 to E. A. Davis for a two compartment water bucket!!!!!!! Seems you just can't trust anyone anymore.

One advertisement for a pick gun tool cautions the reader that complete identification must be provided for ordering this tool which, in the wrong hands, could virtually cause a "crime wave". This is pure bologna! These tools require as much as much, if not more skill than conventional pick- ing and most agree that a skilled picker with a hand pick is better equipped than someone with little or no skills armed with a pick gun. The only application where this tool has an advantage is on cylinders equipped with mushroom pins or other similar pin design which makes conventional picking a lot more difficult, sometimes impossible.   lock lock picking  is a two handed operation with one hand using the conventional torsion wrench to impart a slight turning force. Internally, the pick gun is akin to a double action revolver. Squeezing the long "trigger" forces an internal "hammer" to compress an adjustable spring. Near full compression, the sear releases the hammer for its forward travel at the end of which it hits the pick holder. This causes the pick to travel upward in a snapping motion. If properly held in the keyway it will impart the same motion to the tumbler pins as did Rapping - This subject is hardly worth mentioning, how- ever, since we are discussing, methods of causing all the pins to be thrown into a position whereby the plug can turn, we might touch, briefly, on the technique of "rapping". basically this entails striking the body of the lock with a plastic, rawhide or rubber protective hammer in the opposite direction than the pins have to travel to reach the shear line. This technique has been used with some degree of success in opening padlocks where the latch dog was acted upon by this transfer of force rather than the pins themselves. Most quality pad- locks have had design improvements to preclude to ease of opening by this technique. Snapping, pick guns or rapping all make use of one well known law of physics known as Newton's law. For the benefit of those who slept through physics class this law briefly states that an object in motion or at rest will remain in that state until acted upon by another force. Rocker Picks - This method is another rather hybrid method of opening a lock without the key. Some typical rocker picks are shown in Figure 15. These are usually made for a particular brand or type of lock as the random depth cuts must be fairly accurately spaced apart. The back side of the pick is ground to an oval; hence the name rocker pick. A typical set of these will have 10 or more different picks, the only difference being the different random cuts. The whole idea here is that with enough different cut combinations together with an applied rocking motion once the tool is inserted into the keyway, somewhere along the way all the pins will, by chance, be raised to the shear line at the same time. Picks For Tubular Locks - The typical tubular lock has 7 pins located radically around a center post. This is considered to be a high security lock and is usually found in laundromat equipment, coin changers ,vending machines and bike locks . 

This tool departs from the techniques and principles we have gone over thus far. This tool imparts a turning torque also, and therefore a separate torque wrench is not required. The tool actually impressions more than it picks. It has 7 thin steel fingers that, when a certain in & out motion is applied to the tool while also applying a slight turning force, adjust themselves to correspond to the cut depth of the key that would open the lock. A rubber band or rubber sleeve provides friction to hold the fingers semi-firmly in place. Once the lock opens the fingers are held tighter by applying another rubber band or tightening a rubber sleeve. When this is done the tool can be used as a key to open the lock or as a guide to cut a permanent key on a special key duplicating machine.

COMMERCIALLY AVAILABLE PICKING TOOLS

Pick Sets - Almost as interesting as the evolution of locks is the evolution of lock picking tools (especially in the last few years). Archeological finds indicate lock picking tools have existed almost as long as locks themselves. In latter years professional pick sets for the locksmith trade ranged from two or three basic picks (which most professionals prefer) to a student set of six to ten picks. Now if you really want to impress your peers you can obtain a super deluxe set containing literally dozens of different picks, torsion wrenches, broken key extractors, etc., all contained in a genuine leather, double fold out, zipper closed case!!!

For years this was the way it was pick sets didn't increase in quality or useful design only in the number of picks and fancier cases to hold them. Tool manufacturers finally wised up and in the last few years have introduced smaller, better designed, and more practical sets than before. When pick design stalemates, the manufacturers seem to concentrate on handle design or a novel way to package or contain the pick set. A simple set will do about all a set with dozens of picks will do.

you will see examples of better thought out and more practical pick sets. The trend to adifferent and exotic or novel way to package a pick set. Here an attempt to pre- sent a "jack knife " type of toot set has been done. Actually this approach to pick set packaging is nothing new; the OSS (forerunner of the CIA), during WW 11, designed a pick set contained in a real jack knife handle. Whether this was for convenience of concealment we are not quite sure. Some locksmiths have taken a regular pocket knife and ground picks from the blades. This is a questionable approach as the blades are made from hard and fairly brittle steel, they break too easily.

Yet another approach to this problem is to break or grind off all the regular blade except for about 1/4 in. then silver solder a more conventional pick to the stub thus making a slightly more usable jack knife pick set. Since a torsion wrench is an indispensable part of a pick set, it must be carried separately from the knife. In any case it is refreshing to see manufacturers take a fresh (or at least different) approach to pick set design. Perhaps the most innovative pick set-design to come along recently is the pick set designed into a fountain pen as its "innards". Called a "007" pick set it contains 2 each of 3 basic pick styles: diamond, rake, andfeeler. The need for a torsion wrench was cleverly answered by using the clip, which in this case is removable making a less than perfect, however, usable when Carried in the pocket, along with other pens and pencils, this"007" pick set appears as an innocent felt tip pen

One method of picking and type of lock we haven't yet discussed is the double sided lock. This type of lock is found on storage cabinets, desks and other medium security applications and is referred to as wafer locks. Several years ago they were found on some vending machines. However, the tubular lock has now all but totally replaced them. Do not confuse the locks and keys used on Ford automobiles with double sided locks. The Ford lock is single sided - only the key is double sided, the purpose being that it can be inserted either way.

. Typically, these locks are of disc tumbler construction. You can see how these spring loaded wafers protrude from the plug. Installed into the housing, these wafers prevent the plug from turning.

IMPROVISED PICKING TOOLS

Today there are literally hundreds of commercially available tools for the locksmith. Most of these tools started out as homemade versions and many of the commercially available tools around today can be, and have been duplicated by those handy with hand and machine. Only a few locksmithing tools require expensive or precision manufacturing machinery and processes. Most picks can be made by bending and grinding pieces of steel wire and flat steel spring material. Any flat spring material ranging in thickness from .015 to .035 can he fashioned into a pick with the aid of a small grinder. One of the most common sources of such material is an automotive feeler gauge. These gauges have blades ranging in thickness from .001 to approximately .040 of an inch. "jack knife" pick set which was made from an automotive feeler gauge. There are enough blades in a set like this to allow hand making a complete set of special and custom picking tools and shims.

One of the most original improvised pick sets to show up is This "007" type device was built around a readily available hobby knife. The hollow handle is normally pressed on to the aluminum collet. On the improvised pick set this hollow has been altered to provide a slip fit, allowing it to be readily removed for access to its contents which happen to be a custom pick set together with a small torsion wrench. The clear plastic cap was painted black on the inside. This little jewel turns out to be more incognito than any commercially available set around today.

CONCLUSION

You, the reader, have just seen most of the inner secrets of lock picking. We have looked briefly at some of the more common types of locks and the established ways of picking each one.While the tools used differ, the basic ingredients of skill and dexterity remain the same. Lockpicking is not easy. You may "luck out" sometimes but will usually spend several minutes, sometimes hours before succeeding. No lock picking tool will perform by itself any more than an artists paint brush. Lockpicking is hardly a skill of the fence hopping, run of the mill burglar. He seldom has the knowledge or patience. These operators usually find enough open windows and unlocked doors to satisfy their needs. Lock picking enters the larcenous arena when the stakes are high. These stakes are usually items of high monetary value when burglary is concerned or intelligence gathering where espionage is involved. It is only here where the high security and "pick resistant" locks are really worth their extra cost and only then when combined into an overall physical security system. For the average home owner the extra security afforded by pick resistant locks should be added only after tending to more vulnerable points of security on their premises.

Here at locksmith training merseyside we teach our trainees to pick open every type of lock on the market with shop bought tools and homemade tools.

FOR  MORE INFOMATION CONTACT ME AT dmlocksmithsschool@yahoo.co.uk or phone  Dave on 01744 613202 / 07916262239